Double Carcass Submarine Hose

EMSTEC provide a range of high quality, high performance, oil suction and discharge hoses, extensively used at offshore moorings throughout the world. The EMSTEC Double Carcass Submarine hoses are utilized in high integrity sub-sea installations such as MBM, CALM, SALM configurations (i.e. Steep ‘S’, Lazy ‘S’, Chinese Lantern).

In addition to standard hose carcass (commonly termed ‘primary’ carcass), EMSTEC Double Carcass Submarine hoses incorporate an additional second carcass designed to contain any product escape from the standard carcass as a result of a slow leak or sudden failure. Effective, robust and reliable leak detection and indication system is provided.

The EMSTEC Double Carcass Submarine hoses fully comply with the requirements of the "OCIMF Guide to Purchasing, Manufacturing and Testing of Loading and Discharge Hoses for Offshore Moorings, Fourth Edition – 1991".

All hoses are designed and manufactured under a quality system in accordance with ISO 9001, and is in compliance with Pressure Equipment Directive (PED) 97/23/EC module H (hoses carry CE marking as required).

22210 SDC - End Reinforced without float collars (i.e. under Buoy)

22210 SDC - End Reinforced without float collars

22220 SDC - Main Line without float collars

22220 SDC - Main Line without float collars

22230 SDC - End Reinforced without float collars (i.e. off PLEM)

22230 SDC - End Reinforced without float collars

22240 DSC - Both Ends Reinforced without float collars

22240 DSC - Both Ends Reinforced without float collars

22250 DSC - Reducing Hose without float collars

22250 DSC - Reducing Hose without float collars

22260 DSC - Tail Hose without float collars

22260 DSC - Tail Hose without float collars

Double Carcass Hose Specification

EMSTEC Double Carcass Submarine, Floating & Catenary hoses fully comply with the requirements of the "OCIMF Guide to Purchasing, Manufacturing and Testing of Loading and Discharge Hoses for Offshore Moorings, Fourth Edition – 1991".

Performance Characteristics & Construction

Nominal Bore (mm): 150 (6”), 200 (8”), 250 (10”), 300 (12”), 400 (16”), 500 (20”), 600 (24”)
Standard Length: 9.1M (30’), 10.7M (35’) & 12.2M (40’) (non-standard less than 12.2M also available)
Hose Construction: Liner Tube – NBR based Rubber, resistant to hydrocarbons with aromatic content up to 60% Primary Carcass – Elastomer reinforced with multi-layers of high tensile textile cords and embedded steel wire helix. Secondary Carcass – Elastomer reinforced with multi-layers of high tensile textile cords Floatation Material (Floating Hoses only) – Closed cell foam Outer Cover – Fibre reinforced smooth elastomer cover, esistant to ageing, abrasion, weathering, sunlight, tearing and oil and seawater penetration. (Polyurethane coating available on request).
Flanges: ANSI B16.5 Class 150 or 300 Flat Face (FF), Hot Dip Galvanised in accordance with BS729 Part 1. (Raised Face (RF) flange face available on request).
Pressure Rating: Primary Carcass - 15 BAR, 19 BAR, 21 BAR (higher pressure ratings on request)
Minimum Burst Pressure: Primary Carcass - 75 BAR, 95 BAR, 105 BAR
Secondary Carcass - 30 BAR, 38 BAR, 42 BAR
Flow Velocity: Maximum of 21m/s
Fluid Product: Crude Oil and Liquid Petroleum Products (other than liquefied petroleum gases and liquefied natural gases).
Temperature Range: Fluid Temperature from -20°C to 82°C.
Ambient Temperature from -29°C to 52°C.
Minimum Bend Radius: Submarine Hose - 4 x hose Nominal Bore Diameter.
Floating Hose – 6 x hose Nominal Bore Diameter
Electrical Continuity: Electrically Continuous or Discontinuous as required.
Leak Detection: Pressure compensated leak detection system for Floating, Submarine & Catenary applications.

For information regarding hose types and applications, please refer to relevant EMSTEC hose data sheets.

Design Approval & Quality Assurance

All of the hoses are designed and manufactured under a quality system in accordance with ISO 9001, and is in compliance with Pressure Equipment Directive (PED) 97/23/EC module H (hoses carry CE marking as required).

Prototype Hose manufacture and testing witnessed and verified by Bureau Veritas (Certifying Authority) and GDC International (Industry Consultant).

 

Download as PDF file