with enlarged cuff
with sandwich flange
with vulcanized in steel nipple
armoured with vulcanized in steel nipple
armoured with vulcanized in steel nipple hopper connection
with vulcanized in steel nipple main line
with vulcanized in steel nipple hopper connection type
Discharge Hoses
EMSTEC Discharge Hoses are available for a wide range of applications. Custom built they will serve as flexible elements for e.g. Floating Steel Pipe Lines, as Jet Water Hoses at drag arms, Connecting Hoses in between Cutter Dredger and Discharge Lines, Compensator Hoses for vibration control, etc...
They can be delivered with a simple sandwich flange, vulcanized in steel nipple or with an enlarged cuff to be fastened on a steel pipe for example.
For any queries, please contact us.
Floating Hoses
EMSTEC Floating Hoses are available of different design criteria. In general the Floating Hoses are consisting of an inner discharge hose with build in steel nipples. A floatation body made out of a closed cell PE foam will be built around the entire hose. The floating body is covered by a reinforced rubber shell suitable to withstand severe sea conditions as well as handling influences. EMSTEC floating hoses are available as mainline, special reinforced mooring, tapered connecting hose and other designs.
For any queries, please contact us.
with enlarged cuff
with sandwich flange
with sandwich flange smooth cover
with vulcanized in steel nipple smooth cover
with vulcanized in steel nipple victaulic type
special segment steel cone
with armoured steel cones (replaceable) & sandwich flange
with armoured steel cones (replaceable) & sandwich flange type b
with sandwich flange
with sandwich flange continuous rubber lining
Suction Hoses
EMSTEC Suction Hoses are designed to achieve high bending capabilities even under severe service conditions. Therefore the designs are selected depending on ID of hose, required bending angle and acceptable build in length. This type of hose will be built as ring type, ring type outside smooth, helix type, armoured type or any other special type of hose requested.
For any queries, please contact us.
Steel Cone Lined Suction Hoses
EMSTEC Steel Cone Lined Suction Hoses are custom built to serve the special requirements of our clients. The outer Rubber Hose is acting as a general suction hose or better explained as an outside seal hose. Inside this seal hose steel cones are located by means of bolts. The subject cones can be built of general mild steel or wear resistant steels like Hardox, Creusabro, etc. Worn out cones can be replaced by removing the locking bolts, and re-inserting new cones.
For any queries, please contact us.
Armoured Suction Hoses
EMSTEC Armoured Hoses are common for service of very abrasive materials like cape rock, coral, etc. Depending on the service requirements the hose will be designed either flexible to be used with e.g. a gimbal or universal joint. On the other hand this type of hose might be built very rigid to be used as a gimbal or universal joint replacement, stern swivel replacement hose etc. insure a long service time even though transporting coarse materials. The built in wear rings can be completed in materials like Hardox, Creusabro, etc.
For any queries, please contact us.
Cylindrical End
Enlarged Cuff
Sandwich Flange
Vulcanized in Steel Nipple with Fixed Flange
Vulcanized in Steel Nipple with Rubber Lining and Fixed Flange
Vulcanized in Steel Nipple with Rubber Lining and Swivel Flange
Vulcanized in Steel Nipple with Special Application
Hose end Fittings
EMSTECs Hose end fitting selection is shown above.
For any queries, please contact us.
Discharge Hose 45° Exit with Sandwich Flange
Discharge Hose Bend with Sandwich Flange
Discharge Hose T-Pipe with Sandwich Flange
Pre-Shaped Hoses
EMSTEC provides a range of rubber moulded fittings like Elbows, Y-Pipes, T-Pipes etc...
For any queries, please contact us.
Gimbal Replacement Hose
Gimbal Replacement Hoses are special designed hoses to replace the steel construction of gimbals and universal joints general build into a drag arm to allow the required flexibility. The design incorporates flexibility as well as lateral rigidity to minimize the offset of the single pipe section. Tensile breaking strength is designed as high to achieve the necessary strength required within a drag arm. A jet hose assembly can be established in accordance to the requirements of the user. Subject design will cut maintenance and building cost of a drag arm. Weight of drag arm is diminished. Down time for the replacement/turning of a hose inside a gimbal or universal Joint is lower due to an open access of working area
For any queries, please contact us.